CD-ROM How It Stores Data

how stuff works, CD / DVD

Data CD’s and DVD’s are everywhere these days. Whether they are used to hold music, data or computer software, they have become the standard medium for distributing large quantities of information in a reliable package. Compact discs are so easy and cheap to produce that America Online sends out millions of them every year to entice new users.
In this session, we will look at how CD’s and CD-drives work. We will also look at the different forms CD’s take, as well as what the future holds for this technology.

How Stuff Works: Data Storage On CD / DVD Drives



Understanding the CD: Material

For a Disk that can store up to 74 minutes of music, the total amount of digital data that must be stored on a Disk is:

44,100 samples/channel/second x 2 bytes/sample x 2 channels x 74 minutes x 60 seconds/minute = 783,216,000 bytes

To fit more than 783 megabytes (MB) onto a disc only 4.8 inches (12 cm) in diameter requires that the individual bytes be very small. By examining the physical construction of a Disk , you can begin to understand just how small these bytes are.

A CD is a fairly simple piece of plastic, about four one-hundredths (4/100) of an inch (1.2 mm) thick. Most of a CD consists of an injection-molded piece of clear polycarbonate plastic. During manufacturing, this plastic is impressed with microscopic bumps arranged as a single, continuous, extremely long spiral track of data. We’ll return to the bumps in a moment. Once the clear piece of polycarbonate is formed, a thin, reflective aluminum layer is sputtered onto the disc, covering the bumps. Then a thin acrylic layer is sprayed over the aluminum to protect it. The label is then printed onto the acrylic.


Understanding the CD: The Spiral

A CD has a single spiral track of data, circling from the inside of the disc to the outside. The fact that the spiral track starts at the center means that the Disk can be smaller than 4.8 inches (12 cm) if desired, in fact there are now plastic baseball and business cards that you can put in a CD player. CD business cards hold about 2 MB of data before the size and shape of the card cuts off the spiral.

What the picture does not even begin to impress upon you is how incredibly small the data track is — it is approximately 0.5 microns wide, with 1.6 microns separating one track from the next. (A micron is a millionth of a meter.) And the bumps are even more miniscule.

Understanding the Bumps

The elongated bumps that make up the track are each 0.5 microns wide, a minimum of 0.83 microns long and 125 nanometers high. (A nanometer is a billionth of a meter.)

You will often read about “pits” on a Disk instead of bumps. They appear as pits on the aluminum side, but on the side the laser reads from, they are bumps.

The incredibly small dimensions of the bumps make the spiral track on a disk extremely long. If you could lift the data track off a Disk and stretch it out into a straight line, it would be 0.5 microns wide and almost 3.5 miles (5 km) long!

To read something this small you need an incredibly precise disc-reading mechanism. Let’s take a look at that.

CD Player Components


The CD player has the job of finding and reading the data stored as bumps on the CD. Considering how small the bumps are, the CD player is an exceptionally precise piece of equipment. The drive consists of three fundamental components:

  • A drive motor spins the disc. This drive motor is precisely controlled to rotate between 200 and 500 rpm depending on which track is being read.
  • A laser and a lens system focus on and read the bumps.
  • A tracking mechanism moves the laser assembly so that the laser’s beam can follow the spiral track. The tracking system has to be able to move the laser at micron resolutions.

What the CD Player Does: Laser Focus

Inside the CD player, there is a good bit of computer technology involved in forming the data into understandable data blocks and sending them either to the DAC (in the case of an audio CD) or to the computer (in the case of a CD-ROM drive).

The fundamental job of the CD player is to focus the laser on the track of bumps. The laser beam passes through the polycarbonate layer, reflects off the aluminum layer and hits an

opt-electronic device that detects changes in light. The bumps reflect light differently than the “lands” (witch is the rest of the aluminum layer), and the opt-electronic sensor detects that change in reflectivity. The electronics in the drive interpret the changes in reflectivity in order to read the bits that make up the bytes.

What the CD Player Does: Tracking

The hardest part is keeping the laser beam centered on the data track. This centering is the job of the tracking system. The tracking system, as it plays the CD, has to continually move the laser outward. As the laser moves outward from the center of the disc, the bumps move past the laser faster — this happens because the linear, speed of the bumps is equal to the radius times the speed at which the disc is revolving (rpm). Therefore, as the laser moves outward, the spindle motor must slow the speed of the CD. That way, the bumps travel past the laser at a constant speed, and the data comes off the disc at a constant rate.

CD Encoding Issues


If you have a CD-R drive, and want to produce your own audio CD’s or CD-ROM’s, one of the great things you’ve got going in your favor is the fact that software can handle all the details for you. You can say to your software, “Please store these songs on this Disk,” or “Please store these data files on this CD-ROM,” and the software will do the rest. Because of this, you don’t need to know anything about Disk data formatting to create your own CD’s. However, CD data formatting is complex and interesting, so let’s go into it anyway.

To understand how data are stored on a Disk, you need to understand all of the different conditions the designers of the data encoding methodology were trying to handle.

Because the laser is tracking the spiral of data using the bumps, there cannot be extended gaps where there are no bumps in the data track. To solve this problem, data is encoded using EFM (eight-fourteen modulation). In EFM, 8-bit bytes are converted to 14 bits, and it is guaranteed by EFM that some of those bits will be 1s.

  • Because the laser wants to be able to move between songs, data needs to be encoded into the music telling the drive “where it is” on the disc. This problem is solved using what is known as sub code data. Sub code data can encode the absolute and relative position of the laser in the track, and can also encode such things as song titles.
  • Because the laser may misread a bump, there need to be error-correcting codes to handle single-bit errors. To solve this problem, extra data bits are added that allow the drive to detect single-bit errors and correct them.
  • Because a scratch or a speck on the Disk might cause a whole packet of bytes to be misread (known as a burst error), the drive needs to be able to recover from such an event. This problem is solved by actually interleaving the data on the disc, so that it is stored non-sequentially around one of the disc’s circuits. The drive actually reads data one revolution at a time, and UN-interleaves the data in order to play it.
  • If a few bytes are misread in music, the worst thing that can happen is a little fuzz during playback. When data is stored on a Disk, however, any data error is catastrophic. Therefore, additional error correction codes are used when storing data on a Disk.

CD Data Formats

There are several different formats used to store data on a Disk, some widely used and some long-forgotten. The two most common are CD-DA (audio) and CD-ROM (computer data).

Learn how to make your website load faster..

Join us on Facebook  Powered by MalvaStyle